Parts

- Aheadset preload adjusting bolt

Avid makes it easy to get a perfectly set up brake with their innovative CPS Hardware Kit. Each kit features a series of washers that make it easy to set up your brake. Step 1: Install the bolts and washers loosely so the caliper can move. Step 2: Squeeze the brake lever. Step 3: Tighten the bolts. It's that simple to get a rub-free setup! This kit includes stainless steel hardware with washers and bolts for both CPS (Caliper Positioning System) mounting and standard (direct-mount)mounting.

To keep your Avid brakes functioning properly, check your pads for wear and replace them when necessary. Organic compound pads are softer for quieter braking and increased modulation, while metallic pads dissipate heat better and last a bit longer. Two pads, one retraction spring and a mounting bolt are included (enough for one brake) in each pad set. And, choose an aluminum backing plate if you're really counting the grams.

Avid, Post Bracket, Includes Stainless Caliper Mounting Bolts (CPS and Standard)

To keep your Avid brakes functioning properly, check your pads for wear and replace them when necessary. Organic compound pads are softer for quieter braking and increased modulation, while metallic pads dissipate heat better and last a bit longer. Two pads, one retraction spring and a mounting bolt are included (enough for one brake) in each pad set. And, choose an aluminum backing plate if you're really counting the grams.

Avid, Post Bracket, Includes Stainless Caliper Mounting Bolts (CPS and Standard)

- Includes stainless steel bolts - 40mm fits 200mm Front and 180mm Rear Rotors

To keep your Avid brakes functioning properly, check your pads for wear and replace them when necessary. Organic compound pads are softer for quieter braking and increased modulation, while metallic pads dissipate heat better and last a bit longer. Two pads, one retraction spring and a mounting bolt are included (enough for one brake) in each pad set. And, choose an aluminum backing plate if you're really counting the grams.

Cost effective stopping power from the leader in cable-actuated disc brakes. - All calipers have 74mm mounting bolt spacing - For use with with long cable-pull levers - Mono-block caliper design has outboard pad adjustment - Spring tension is adjustable - Includes steel-backed organic pads - Brake Caliper Type: Post Mount - Brake Lever Actuation: Long Pull - Rotor Included: No - Weight: 215 g

Clean up your handlebar with Avid's MatchMaker X clamp. It combines mounts for your SRAM shifters and Avid brake levers into one simple, sleek unit so you can shed grams and keep your bars nice and tidy. You can also integrate RockShox's XLoc remote (sold separately) for maximum convenience and ease of use.

Clean up your handlebar with Avid's MatchMaker X clamp. It combines mounts for your SRAM shifters and Avid brake levers into one simple, sleek unit so you can shed grams and keep your bars nice and tidy. You can also integrate RockShox's XLoc remote for maximum convenience and ease of use.

Triggy Alpha - The name speaks for itself - the new pack leader of dropper remotes. Since the beginning our Triggy has proven to be a favourite among many many pro riders and testers but with Triggy Alpha we have now set the bar even higher and we confidently say: There is no better remote on the market. The video is pretty much explaining very well what makes Triggy Alpha stand out amongst others: - Ball bearing on the paddle - Angle-adjustable paddle - Black anodized aluminum body and paddle with laser engraved finish - 2 available paddle lengths for crisp or soft dropper engagement - 2 mounting holes - Integrated cable tensioner - Direct mount for almost any brake available (see mounting options) - New cable clamping for universal dropper compatibility - Extremely low weight: 32g/34g (short/long) - Maximum cable pull: 11 mm The short version mimics our proven original Triggy paddle geometry. The long variant features a 7mm longer paddle and reduces the required forces by about 15%. Triggy Alpha is compatible with any commonly available aftermarket cable-actuated dropper post on the market. 1 set Triggy Alpha includes: - 1x Triggy Alpha remote (short or long) - 1x shift cable - 1x wire endcap - 1x BikeYoke Splits Clamp or I-Spec Adapter (optional)

3 years of REVIVE out in the market resulted in another benchmark product for BikeYoke: REVIVE 2.0. The new extralong 213mm REVIVE required a lot of re-thinking and re-engineering the whole chassis structure and since we think they deserve it, the shorter REVIVES will also get all the nice updates, and benefit from what was originally implemented only for the longest sibling of the REVIVE family. Noteworthy updates of the REVIVE 2.0 include: - One piece 3D-forged upper tube unit for improved stiffness and strength - Fully hard-anodized pin seats in the upper tube for improved corrosion-resistance - CNC-finished actuation lever for even smoother engagement - New upper saddle clamp and saddle bolts with integrated conical washers for even simpler saddle installation Wanna know more about the REVIVE? What if there was a dropper post, that actually solves and not just improves reliability issues, saves cost and time on the long run, and does not let you worry about too much time spent at service-centers? Or how about “bleeding” your seat post within a few seconds, while it is still installed in your bike? BikeYoke presents the REVIVE dropper post, featuring one of the most brilliant design features in dropper post design in many years. More than 10 years of experience in drop-post design went into the “REVIVE” and the development has finally paid off. Of, course, just as many other companies, BikeYoke would say, that REVIVE is reliable and strong and smooth. And yes, REVIVE is all of that, but not because we tried to improve current designs, but because we were thinking outside of the box and created a new concept, that is completely different from everything before. To understand the benefits over other posts you have to know about the problems of many current designs first. Many of the popular current seatpost designs are based on a hydraulic lockout-system that relies on a perfectly sealing IFP (Internal Floating Piston), separating oil from air to prevent the seatpost from getting sagging or bouncing. There are a lot of difficulties to overcome when using an IFP because an IFP has to maintain 100% sealing function. If air could go to the oil side, your post will start becoming springy. This happens to a lot of posts in the market already and is the main issue why posts need to be serviced. That´s why BikeYoke´s “REVIVE” features a NON-IFP design, because we think it is too difficult - if not impossible - to make a really reliable design using an IFP. REVIVE only requires 2 dynamic seals in the hydraulic circuit: The shaft sealing and the main piston sealing for the lockout mechanism. The highly critical IFP has been removed, and with it the need of perfect concentricity and finish of the sealing surfaces of the tubes. The lack of an IFP also results in the smoothest action you can think of. The most important and ground-breaking feature of Revive is its “REVIVE-VALVE”. Even REVIVE can get air somewhere where it does not belong. This can happen for example when you actuate your seatpost while its upside down. And here is where the patented RESET VALVE comes into play: - Insert a 4mm Hex Key into the REVIVE hex port, turn it and push down the post by hand. - This will reset your hydraulic circuit on the fly - whenever. wherever. This is done just within a few seconds and only by the turn of a 4mm Allen key or the integreated mini reset lever, that comes with the post - of course without even having to remove your drop post from your bike. So, now one might already understand that: - No external air will want go inside the post´s hydraulic circuit, since it is charged with higher pressure, than its surroundings. - No oil will go out (or at least very very little oil over the curse of a long time), because of very stable sealing - external sealing has never been a real problem of current post design - The hydraulic system can be reset to “new” via the unique “REVIVE-valving” - This means the hydraulic circuit is a very stable closed system and basically maintenance free. Still there are parts that will need to be serviced sooner or later and when designing REVIVE it was put a lot of attention to maximum user-friendly serviceability: - Bushings and keyway pins will wear over time. Usually, the pins wear first and you would want to replace them to reset your rotational play. - Exchanging the pins and the lower bushing is simple and does not require any opening of the hydraulic system and can be done within less than 5 minutes. 1 set REVIVE dropper post includes: - 1x REVIVE Seatpost - 1x cable housing 1500mm - 1x inner wire 1700mm - 2x housing endcap - 1x barrel cable clamp - 1x air valve adapter - 1x Quick-Reset-Lever - 1x remote (optional) - 1x BikeYoke I-spec adapter or Splits Clamp (optional) - 1 set titanium saddle bolts and nuts (optional)

- Designed for linear pull & mechanical disc brakes - Aluminum construction - 2.5 finger - 22.2mm (7/8-inch) clamp - Left/Right: Right - Reach adjust and return spring - 88g each

- Hardpack mountain bike tire designed to run in specific directions for the front and rear - In front, the Camber rolls fast, confidently grabbing corners even in the loose stuff - Reversed on the rear, the Camber gives you the same confidence in the corners, plus additional acceleration and climbing traction - Folding bead option also provides lightweight EPS puncture protection layer for outstanding performance and durability

The Patrol is an all-condition XC trail tire that excels on hardpacked to loose conditions. - Medium-height ramped center knobs roll fast and provide climbing traction - Aggressive shoulder lugs deliver secure traction in corners - Durable 27 TPI casing

- Versatile tread pattern suitable for a broad range of conditions - Medium-height center knobs are ramped to reduce rolling resistance and are staggered to provide a consistent feel across the profile of the tire - Side knobs are fairly aggressive and provide excellent cornering grip - Available with a wire bead or folding bead with EPS puncture protection

- Versatile tread pattern suitable for a broad range of conditions - Medium-height center knobs are ramped to reduce rolling resistance and are staggered to provide a consistent feel across the profile of the tire - Side knobs are fairly aggressive and provide excellent cornering grip - Available with a wire bead or folding bead with EPS puncture protection

Shim spacers can be placed between bearing and compression cover in IS headsets to fine tune the fitment.

Compression ring fits above the upper bearing in a Cane Creek headset to ensure vertical and horizontal compression is optimal. - Compatible with 41mm and 42mm OD upper bearings

40-Series Bearing - Compatible with 110-, 40-, and 10-Series headsets

40-Series Bearing - Compatible with 110-, 40-, and 10-Series headsets

Crown races for Cane Creek headsets fit a variety of lowers and crown race seat diameters. - Compatible with 10-, 40- and 110-Series headsets and backwards compatible with S and XX Series - Integral mold seals keep out the elements - Durable steel construction

Crown races for Cane Creek headsets fit a variety of lowers and crown race seat diameters. Compatible with 10-, 40- and 110-Series headsets and backwards compatible with S and XX Series - Integral mold seals keep out the elements - Compatible with 52mm lower headset bearings - Compatible with 40mm (1-1/2") tapered steerer tubes - Durable steel construction

Mounting hardware fits a variety of Cane Creek shocks.

Bearings for Cane Creek AER headsets. - Aluminum Bearing

40-Series Bearing - Compatible with 110-, 40-, and 10-Series headsets

Super-smooth steering, quality materials, cutting-edge design and serious durability are all hallmarks of Cane Creek's 40-Series headsets. • Technical Description: IS52/30/H1 • Bottom Type: IS - Integrated • Bottom Head Tube Inside Dia.: 52.1mm • Crown Race Seat Dia.: 30.015mm • Crown Race Type: Steel, Face-Sealed • Bottom Stack Height: 1mm • Bottom Bearing Type: Black Oxide, Sealed • Material: N/A • Weight: 72g

40-Series Bearing - Compatible with 110-, 40-, and 10-Series headsets

Super-smooth steering, quality materials, cutting-edge design and serious durability are all hallmarks of Cane Creek's 40-Series headsets. • Technical Description: ZS49/30/H4/K • Bottom Type: ZS - ZeroStack • Bottom Head Tube Inside Dia.: 49.61mm • Crown Race Seat Dia.: 30.015mm • Crown Race Type: Steel, Face-Sealed • Bottom Stack Height: 4mm • Bottom Bearing Type: Black Oxide, Sealed • Material: 6061 aluminum • Weight: 58g